How To Thread Brother Ls 2125

Close up of a Brother LS-2125i Sewing Machine

My married man was given this sewing auto in hopes he knew someone who could employ it. It was missing the presser foot and needed a needle, merely other than that, the sewing motorcar seems to work simply fine. I had never used a Brother sewing car earlier, then for me this was new territory. Only it wasn't long before I had it all prepare for sewing. Hither is how I threaded the sewing automobile.

How to Thread a Brother Sewing Motorcar

Threading the top thread into this motorcar wasn't very hard, however the thread take-up lever does not come up up every bit far out of the casing as other machines I have used. It may take a moment of fidgeting with it for you to get the thread effectually it. Here are the steps for threading this sewing machine.

Place your spool of thread onto the spool pivot.
Have the stop of your thread and pass information technology over the thread guide as shown in the pic on the top of the automobile next to the thread guide.
Run the thread down and effectually the upper tension command dial and back up the other side.
Now run the thread dorsum up to the thread take-up and go over it from left to correct. The thread should catch and become into the grove.
So take the thread dorsum downwards the front of the machine to the sewing needle housing. In that location volition exist a thread guide at the elevation of the needle. Run the thread through the guide, then snip the end of your thread and thread your needle from front to back.

How to Wind a Bobbin on a Brother Sewing Automobile

Winding a bobbin on a Brother sewing motorcar is pretty much just similar winding on whatever of the other machines I accept used. With this auto though, there is no clutch to pull out and so its ane less stride. Hither are the steps for winding a bobbin on a brother sewing machine.

Place your spool of thread on the spool pin.
Run the thread to the thread guide on the left and wrap it effectually according to the picture on top of the automobile.
At present run the thread back to your bobbin winder.
Have your empty bobbin and run your thread from the eye of the bobbin, upwards into one of the little holes in the pinnacle deejay.
Pull the thread long enough to hold it out of the fashion and place the bobbin on the bobbin winder with the thread pointed upward.
Now holding the end of your thread in your right manus (you can guide the thread from the spool with your left), press your pedal slowly to outset the bobbin winding.
In one case you take the bobbin started, you can trim the extra thread from the summit.
End winding the bobbin and when it stops, push the bobbin winder to the left and gently pull upwardly to remove it from the machine.
Cutting the thread and you are washed.

How to Put the Bobbin in a Brother Sewing Automobile

This sewing car has a front load bobbin. It can be difficult at times, peculiarly if you lot have fumbly fingers like I do, just with a fiddling patience, it will accept no time to install this bobbin. Here are the steps for how to install the bobbin.

Remove the front section of casing over the bobbin housing and open the bobbin door.
Remove your bobbin case by pulling the silver bar that runs across the middle on the left hand side. The silver bar should lift upwards allowing you to remove the whole instance.
Belongings the silver case with the open side towards you, identify your filled bobbin into information technology. Make certain to pull the thread to a couple of inches long and then you lot can thread the bobbin.
Now property the silver bobbin case with the arm (the weird alien L shaped piece on the side with the bar) facing upwards and open side facing you lot. take the thread and run it upward through the thread guide and into the opening adjacent to the arm.
Holding the casing by the open bar, identify the bobbin casing in to the bobbin housing with the arm and pigsty you merely threaded facing upwards.
In one case it is in place, with you meridian thread already threaded, rotate your mitt wheel on the right side of the machine until the needle goes downward into the bobbin housing and and so back upwardly.
Take a scissors or flat object and run it from right to left under the presser pes. This should bring the thread up to join the summit thread. Pull both threads a couple of inches then move them to the side and out of the fashion. If the bobbin thread does not come up up the first time, echo the steps for rotating the hand wheel until it brings upwardly the thread.
Shut the bobbin door and replace the front of your example.

Delight keep in mind that we may receive a minor committee when you click our links and brand purchases and equally an Amazon Associate, this site earns from qualifying purchases. However, this does not impact our reviews and comparisons. Nosotros endeavor our all-time to give you an accurate representation, in guild to help y'all make the best pick for you.